Nedávno jsem se setkal s problémem jak nastavit délku funkce FLASH na starším FAXU Panasonic KX-F130 nebo KX-F2130. Po delší době se mi podařilo najít následující tabulku servisních funkcí. Jen pro upřesnění do servisního menu se dostanete stiskem tlačítka PROGRAM nasledovaný tlačítky #9000*. V menu můžete nastavovat od všech konstant přístroje (FLASH, DTMF ...) po otestování motorů faxu a podobných detailů. Pokud se s přístrojem setkáte v opravně určitě se bez menu neobejdete.
Panasonic KX-F130
SERVICE FUNCTION TABLE
+----+------------------------+---------+---------------+-------+---------+
|Code| Function |Set Value|Effective Range|Default| Remarks |
+----+------------------------+---------+---------------+-------+---------+
| 501| Pause time set | x100 ms.| 000 - 600 | 050 | |
+----+------------------------+---------+---------------+-------+---------+
| 502| Flash time set | x10 ms. | 01 - 99 | 70 | |
+----+------------------------+---------+---------------+-------+---------+
| 503| Dial speed select | 1..10PPS| 1,2 | 1 | |
| | | 2..20PPS| | | |
+----+------------------------+---------+---------------+-------+---------+
| 510| VOX time select | 1..6 sec| 1,2 | 1 | |
| | | 2..4 sec| | | |
+----+------------------------+---------+---------------+-------+---------+
| 520| CED frequency select |1..2100Hz| 1,2 | 1 | |
| | |2..1100Hz| | | |
+----+------------------------+---------+---------------+-------+---------+
| 521| International mode | 1.. On | 1,2 | 1 | |
| | select | 2.. Off | | | |
+----+------------------------+---------+---------------+-------+---------+
| 522| Auto recovery select | 1.. On | 1,2 | 1 | |
| | | 2.. Off | | | |
+----+------------------------+---------+---------------+-------+---------+
| 523| Receive equalizer | 1..0,0Km| 1-4 | 2 | |
| | select | 2..1,8Km| | | |
| | | 3..3,6Km| | | |
| | | 4..7,2Km| | | |
+----+------------------------+---------+---------------+-------+---------+
| 524| Transmit equalizer | 1..0,0Km| 1-4 | 2 | |
| | select | 2..1,8Km| | | |
| | | 3..3,6Km| | | |
| | | 4..7,2Km| | | |
+----+------------------------+---------+---------------+-------+---------+
| 550| Memory clear (Refer to page "Test functions") |"START" |
| | Returns the set values of #04-#22 (user selectable) to | input |
| | default. | |
+----+------------------------------------------------------+---+---------+
| 551| ROM check (Refer to page "Test functions") |"START" input|
+----+------------------------+---------+---------------+---+---+---------+
| 552| DTMF single tone trans-| 1.. On | 1,2 | 2 | |
| | mit select | 2.. Off | | | |
+----+------------------------+---------+---------------+-------+---------+
| 553| Monitor on FAX |1.. all | 1-3 | 3 | |
| | communication select |2.phase B| | | |
| | |3.. Off | | | |
+----+------------------------+---------+---------------+---+---+---------+
| 554| Modem test (Refer to page "Test functions") |"START" input|
+----+------------------------------------------------------+-------------+
| 555| Scanner test (Refer to page "Test functions") |"START" input|
+----+------------------------------------------------------+-------------+
| 556| Motor test (Refer to page "Test functions") |"START" input|
+----+------------------------------------------------------+-------------+
| 557| LED test (Refer to page "Test functions") |"START" input|
+----+------------------------------------------------------+-------------+
| 558| LCD test (Refer to page "Test functions") |"START" input|
+----+------------------------+---------+---------------+---+---+---------+
| 559| Paper jam detection | 1.. On | 1,2 | 1 | |
| | select | 2.. Off | | | |
+----+------------------------+---------+---------------+---+---+---------+
| 561| KEY test (Refer to page "Test functions") |"START" input|
+----+------------------------+---------+---------------+---+---+---------+
| 563| CCD position adjustment| x1 mm | 00 - 30 | 15 | |
| | value set | | | | |
+----+------------------------+---------+---------------+-------+---------+
| 570| BREAK % select | 1.. 61% | 1,2 | 1 | |
| | | 2.. 67% | | | |
+----+------------------------+---------+---------------+-------+---------+
| 571| ITS auto redial time |x number | 00 - 99 | 14 | |
| | set |of times | | | |
+----+------------------------+---------+---------------+-------+---------+
| 572| ITS auto redial line |x second | 001 - 999 | 030 | |
| | disconnect time set | | | | |
+----+------------------------+---------+---------------+-------+---------+
| 573| Remote turn-on ring |x number | 01 - 99 | 15 | |
| | number set | of rings| | | |
+----+------------------------+---------+---------------+-------+---------+
| 574| Dial Tone Detection set| 1.. On | 1,2 | 2 | |
| | | 2.. Off | | | |
+----+------------------------+---------+---------------+-------+---------+
| 580| TAM sequential tone | 1.. On | 1,2 | 1 | |
| | detection select | 2.. Off | | | |
+----+------------------------+---------+---------------+-------+---------+
| 581| ICM Tape End Detection | 1.. On | 1,2 | 2 | |
| | set | 2.. Off | | | |
+----+------------------------+---------+---------------+-------+---------+
| 582| 2-way recording select |1..Enable| 1,2 | 1 | |
| | set |2.Disable| | | |
+----+------------------------+---------+---------------+-------+---------+
| 583| 2-way beep time set | x1 ms | 000 - 999 | 000 | |
+----+------------------------+---------+---------------+-------+---------+
| 586|White line skip 1 select|1.. On | 1,2 | 1 | |
| | |2.. Off | | | |
+----+------------------------+---------+---------------+-------+---------+
| 587|White line skip 2 select|1.. On | 1,2 | 1 | |
| | |2.. Off | | | |
+----+------------------------+---------+---------------+-------+---------+
| 590| FAX auto redial time |x number | 00 - 99 | 05 | |
| | set |of times | | | |
+----+------------------------+---------+---------------+-------+---------+
| 591| FAX auto redial line | x second| 001 - 999 | 045 | |
| | disconnect time set | | | | |
+----+------------------------+---------+---------------+-------+---------+
| 592| CNG transmit select |1.. auto/| 1-3 | 1 | |
| | | manual| | | |
| | |2.. auto | | | |
| | |3.. Off | | | |
+----+------------------------+---------+---------------+-------+---------+
| 593| Time between CED and |1..75 ms | 1,2,3 | 1 | |
| | 300 bps |2..500 ms| | | |
| | |3..1 sec | | | |
+----+------------------------+---------+---------------+-------+---------+
| 594| Overseas DIS detection |1.detects| 1,2 | 1 | |
| | select | at the | | | |
| | | 1st time | | |
| | |2.detects| | | |
| | | at the | | | |
| | | 2st time | | |
+----+------------------------+---------+---------------+-------+---------+
| 595| Receive error limit |x number | 000 - 999 | 100 | |
| | value set | of times| | | |
+----+------------------------+---------+---------------+-------+---------+
| 596| Transmit level set | x dBm | -15 - 00 | 10 |The values
| | | | | |entered |
| | | | | |without |
| | | | | |"minus |
| | | | | |sing" will
| | | | | |be regar-|
| | | | | |ded as |
| | | | | |negative.|
+----+------------------------+---------+---------------+-------+---------+
| 597| Transmit speed 2400 BPS| 1.. On | 1,2 | 2 | |
| | fixed mode select | 2.. Off | | | |
+----+------------------------+---------+---------------+-------+---------+
| 717| Transmit speed select |1.9600BPS| 1-4 | 1 |The fall |
| | |2.7200BPS| | |back |
| | |3.4800BPS| | |starts |
| | |4.2400BPS| | |from each|
| | | | | |speed. |
+----+------------------------+---------+---------------+-------+---------+
| 718| Receive speed select |1.9600BPS| 1-4 | 1 |The fall |
| | |2.7200BPS| | |back |
| | |3.4800BPS| | |starts |
| | |4.2400BPS| | |from each|
| | | | | |speed. |
+----+------------------------+---------+---------------+-------+---------+
| 719| Ringer Off in TEL/FAX | 1.. On | 1,2 | 1 |Select |
| | mode | 2.. Off | | |whether |
| | | | | |the rings|
| | | | | |is on or |
| | | | | |off when |
| | | | | |the unit |
| | | | | |receives |
| | | | | |an inco- |
| | | | | |ming sig-|
| | | | | |nalin the|
| | | | | |TEL/FAX |
| | | | | |mode when|
| | | | | |the ringer
+----+------------------------+---------+---------------+-------+---------+
| 720| Manual tone detect | 1.. On | 1,2 | 2 |Sets the |
| | | 2.. Off | | |tone |
| | | | | |detection|
| | | | | |mode after
| | | | | |dialling |
| | | | | |manually.|
+----+------------------------+---------+---------------+-------+---------+
| 731| CPC mode select | 1.. A | 1,2 | 1 | |
| | | 2.. B | | | |
+----+------------------------+---------+---------------+---+---+---------+
| -- | User setting list output |"START" input|
+----+------------------------------------------------------+-------------+
DTMF signale tone transmit select.
When set ON (=1), the 12 keys and
transmission frequencies are as shown.
+-----+----------------+-----+----------------+
| Key | Frequency (Hz) | Key | Frequency (Hz) |
+-----+----------------+-----+----------------+
| "1" | 697 | "5" | 1209 |
+-----+----------------+-----+----------------+
| "2" | 770 | "6" | 1366 |
+-----+----------------+-----+----------------+
| "3" | 852 | "7" | 1477 |
+-----+----------------+-----+----------------+
| "4" | 941 | | |
+-----+----------------+-----+----------------+
When set OFF (=1), the 12 keys and
transmission frequencies are as shown.
+----------+-----------+------+------+------+
| Low (Hz) | High (Hz) | 1209 | 1366 | 1477 |
+----------+-----------+------+------+------+
| 697 | | "1" | "2" | "3" |
+----------+ +------+------+------+
| 770 | | "4" | "5" | "6" |
+----------+ +------+------+------+
| 852 | | "7" | "8" | "9" |
+----------+ +------+------+------+
| 941 | | "*" | "0" | "#" |
+----------+-----------+------+------+------+
TEST FUNCTIONS
+-----------+--------------+----------------+----------------------------+
| | | Code | |
| Test mode | Type of Mode |----------------| Function |
| | | Operation after| |
| | | code input | |
+-----------+--------------+----------------+----------------------------+
| PRINT TEST| User mode | 2 8 |Print a test pattern and |
| | |----------------|check the termal head for |
| | | START |abnormalities (missing dots,|
| | | |etc.), and also check the |
| | | |operation of the reception |
| | | |motor. |
+-----------+--------------+----------------+----------------------------+
| MOTOR TEST| Service Mode | 5 5 6 |Rotate the transmission and |
| | |----------------|reception motors to check |
| | | START |the operation of the motors.|
+-----------+--------------+----------------+----------------------------+
| MODEM TEST| Service Mode | 5 5 4 |Send four kinds of FAX sig -|
| | |----------------|nals to check the sending |
| | | START |function of the modem. |
| | | |1) 1100 Hz: Consecutive sig-|
| | | | nal of EOM for tonal. |
| | | |2) 2100 Hz: G2 carrier sig -|
| | | | nal. Consecutive of CED |
| | | | signal. |
| | | |3) G3, V29 training signal |
| | | | [modulation wave of car- |
| | | | rier signal (1700 Hz)] |
+-----------+--------------+----------------+----------------------------+
| ROM CHECK | Service Mode | 5 5 1 |Indicate the version and |
| | |----------------|check sum of the ROM. |
| | | START | |
+-----------+--------------+----------------+----------------------------+
| SCAN CHECK| Service Mode | 5 5 5 |Turn on the LEDs of the image
| | |----------------|sensor and operate the read |
| | | START |system. |
+-----------+--------------+----------------+----------------------------+
| LCD CHECK | Service Mode | 5 5 8 |Check the LCD indication. |
| | |----------------|Illuminate all dots to check|
| | | START |if they are normal. |
+-----------+--------------+----------------+----------------------------+
| DTMF | Service Mode | 5 5 2 |Output the DTMF by single |
|SINGLE TEST| |----------------|tone |
| | | 1.. On | |
| | | 2.. Off | |
+-----------+--------------+----------------+----------------------------+
| LED TEST | Service Mode | 5 5 7 |All LEDs flashes on and off,|
| | |----------------|or is illuminated. |
| | | START | |
+-----------+--------------+----------------+----------------------------+
| KEY CHECK | Service Mode | 5 6 1 |Check the operation button. |
| | |----------------|Indicate the button code at |
| | | { any } |LCD after the button is |
| | | START { }|pressed. |
| | | { key } | |
+-----------+--------------+----------------+----------------------------+
| FACTORY | Service Mode | 5 5 0 |Clear the memory in which |
| SET | |----------------|the user can store data. |
| | | START | |
+-----------+--------------+----------------+----------------------------+
|